Got a Vaporesso XROS? You are probably already liking its sleek design and exceptional vaping. However, you will one day have to fill your pod. No worries! Filling your XROS tank is straightforward- simple, swift and free of mess when done correctly. And, given a little bit of care, your pods will continue to provide you with that high-quality flavour with no fuss.
In this guide, let’s discover Vaporesso XROS pods.
How to refill Vaporesso XROS Pods?
Step 1: Taking out the Pod
To crack on with this, take that pod out of your Vaporesso XROS. Just pick up the vape and push out the pod. It is supposed to come out effortlessly.
Step 2: Locate the Fill Port
Once the pod is out, let’s find the fill port. On the XROS, it’s located right at the top of the pod. You’ll see a small silicone covering. To open it up, take it off.
Step 3: Fill the e-liquid
Fill up time! Looking forward to filling the pod, grab your favourite e-liquid.
This is how you go about it:
- Pop the head of your e-liquid bottle into the fill hole.
- Gently squeeze the bottle in order to force the liquid into it.
- Don’t overfill it! The result of being overfilled is leaking or gurgling when you vape.
Step 4: Insert the Pod Back in
When filled, keep the pod in the vape. Be sure to lock it in place. This makes it so that there is no leakage and everything is retained.
Step 5: Prime the Coil
In case it is a new pod that you are filling, here is one tip you cannot afford to miss: prime the coil. All this means is letting the pod sit for 3 to 5 minutes after filling it. It gives the cotton in the coil a chance to be soaked to the full with the e-liquid.
Ways to look after your Vaporesso XROS Pods
Chain Vaping must be avoided.
It may be difficult to resist chain vaping (the act of puffing one right after the other). However, this can burn the cotton and make the coil overheat. This causes a burned-out taste and depletes the lifespan of your pod.
Rather, with a couple of puffs, take a break to give the coil time to cool. This way, your pod will last far longer, and you will continue to enjoy smooth hits each time.
E-Liquid Should Be Right
To obtain optimum results, one should use nicotine salt e-liquids or 50/50 PG/VG blends. They are compatible with the Vaporesso XROS pods, and they provide adequate wicking, resulting in flavoursome hits.
Enjoy the amazing flavour of your choice!
Don’t Let the Pod Run Out
This is the important one: never leave your pod dry. When you vape on a dry coil, you burn the cotton and recover burnt flavour.
Be careful of the e-liquid level, and when it reaches empty, refill up. This will preserve your coil and keep things in a smooth manner.
Replace when needed
Pods do not last forever, however, even with great maintenance. When you begin to recognise poor flavour, a loss of vapour, or a burnt taste, it is time to connect a new pod.
Common problems and solutions with Vaporesso XROS Pod
Dry Hits
A dry hit or burnt flavour is one of the worst experiences. This usually happens when the e-liquid doesn’t properly saturate the wick in the coil or when the coil burns out.
Solution:
1. First, make sure the levels of the e-liquid in the tank are enough before vaping. There should be a sufficient amount of liquid that could saturate the wick.
2. Allow short breaks when you are taking a puff so that the coil can absorb the liquid. Excessive use may result in a dry coil, resulting in burnt hits.
Leakage of Vape Juice
The other issue that is commonly raised by users is the problem of leakage of the vape juice, which can cause a mess. It will ultimately lead to a poor experience of the vape session.
Solution:
1. Leaks are common where the seals are not fitted too tightly. In case you detect some leakages, seal them very cautiously.
2. Don’t store your vape at extreme temperatures. Also, sure, it is standing upright so that the e-liquid does not leak. Overheating of e-liquid can also cause leakage sometimes.
Vape Not Producing Vapour
You can also experience a problem in which your vape switches on, and no vapour comes out. It is a very common issue that can be resolved easily.
Solution:
1. First, examine the airflow holes to see whether they are blocked or not. In case these are congested with dust or any other form of debris, clean them thoughtfully using a cotton bud.
2. If you clean it properly and it still doesn’t work, the issue may lie with the vape itself.
Conclusion
Refilling and maintaining your Vaporesso XROS pods is as easy as 1-2-3. If you follow these simple steps and tips, you get:
- Better flavour with every refill
- Longer pod life, saving you money
- No more burnt hits or leaks
Its design makes the Vaporesso XROS very convenient; however, with a bit of care, you shall improve your vaping experience. That is why the next time your pod gets low, just follow these steps and have a fresh, clean, flavourful hit every time!
